Wanguard and Wansight can be installed on x86_64 architectures quickly and easily with the YUM (DNF) package manager. All packages were tested on a stock Rocky Linux 8.x which will reach End Of Life (EOL) on May 2029.
Below you can find the installation steps for Console, Sensor, Filter and BGP Connector.

USER GUIDES:	Wanguard 8.4 User Guide
	Wansight 8.4 User Guide

CONSOLE INSTALLATION STEPS:	Step 1. Install the Andrisoft repository First, make sure that the Andrisoft repository is installed. [root@localhost ~]# rpm -Uvh https://packages.andrisoft.com/rhel8/wanrepo-8.4-0.noarch.rpm [root@localhost ~]# yum update Step 2. Install the packages Install the wanconsole package and its dependencies. Configure and start chrony (ntpd alternative) to prevent clock de-synchronization issues. [root@localhost ~]# yum install wanconsole [root@localhost ~]# cpanm Net::Telnet [root@localhost ~]# systemctl start chronyd [root@localhost ~]# systemctl enable chronyd Step 3. Configure the MariaDB service MariaDB is a drop-in replacement for MySQL. Start MariaDB and set a password for the root database user. If you will deploy Sensors or Filters on remote systems, make sure that the MariaDB server is accessible by opening port TCP/3306 in the firewall. [root@localhost ~]# nano /etc/my.cnf.d/mariadb-server.cnf #set max_allowed_packet=256M, max_connections=1000, open_files_limit=5000 and add skip-name-resolve and sql-mode="NO_ENGINE_SUBSTITUTION" in the [mysqld] section [root@localhost ~]# systemctl start mariadb [root@localhost ~]# mysql_secure_installation [root@localhost ~]# systemctl start mariadb [root@localhost ~]# systemctl enable mariadb [root@localhost ~]# firewall-cmd --permanent --add-service=mysql [root@localhost ~]# systemctl restart firewalld Step 4. Configure the Apache service Disable SELinux and configure the firewall to open port TCP/80 and TCP/443. [root@localhost ~]# nano /etc/php.ini #set date.timezone in the [Date] section, according to http://php.net/manual/en/timezones.php [root@localhost ~]# systemctl enable httpd [root@localhost ~]# systemctl restart httpd [root@localhost ~]# systemctl restart php-fpm [root@localhost ~]# setenforce 0 ; nano /etc/selinux/config #set SELINUX=disabled [root@localhost ~]# firewall-cmd --permanent --add-service=http [root@localhost ~]# firewall-cmd --permanent --add-service=https [root@localhost ~]# systemctl restart firewalld Step 5. Install the database Finish installing the Console by running the /opt/andrisoft/bin/install_console script. Enter the MySQL root password you set in step 3 and set a password for a new database named "andrisoft". In this distribution, the recommended database storage engine is Aria. [root@localhost ~]# /opt/andrisoft/bin/install_console [root@localhost ~]# systemctl restart httpd Step 6. Configure the WANsupervisor service The WANsupervisor daemon must be installed and started on all systems. You have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password you set in step 5. [root@localhost ~]# /opt/andrisoft/bin/install_supervisor [root@localhost ~]# systemctl start WANsupervisor [root@localhost ~]# systemctl enable WANsupervisor Step 7. Install InfluxDB Install influxdb from https://portal.influxdata.com/downloads or the link listed below and execute /opt/andrisoft/bin/install_influxdb to initialize the influxdb database. [root@localhost ~]# wget https://dl.influxdata.com/influxdb/releases/influxdb-1.8.10.x86_64.rpm [root@localhost ~]# yum localinstall influxdb-1.8.10.x86_64.rpm [root@localhost ~]# cp /etc/influxdb/influxdb.conf /etc/influxdb/influxdb.conf.backup [root@localhost ~]# cp /opt/andrisoft/etc/influxdb.conf /etc/influxdb/influxdb.conf [root@localhost ~]# systemctl restart influxdb [root@localhost ~]# /opt/andrisoft/bin/install_influxdb Step 8. Access the Console The Console web interface is accessible by pointing your web browser to http://<hostname>/wanguard or http://<hostname>/wansight, where <hostname> is the name of the server running the Console. The default username is "admin" with the password "changeme". It is highly recommended to install an SSL certificate in Apache to be able to connect securely to Console via HTTPS.

SENSOR INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Install the Andrisoft repository. On the Console server, the Sensor is already installed so you don't need to follow the installation steps listed below. [root@localhost ~]# rpm -Uvh https://packages.andrisoft.com/rhel8/wanrepo-8.4-0.noarch.rpm [root@localhost ~]# yum update Step 2. Install the packages Install the wansensor package and its dependencies. Configure and start chrony (ntpd alternative) to prevent clock de-synchronization issues. [root@localhost ~]# yum install wansensor [root@localhost ~]# cpanm Net::Telnet [root@localhost ~]# systemctl start chronyd [root@localhost ~]# systemctl enable chronyd Step 3. Configure and start the WANsupervisor service This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the WANsupervisor service, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console IP address and database password. [root@localhost ~]# /opt/andrisoft/bin/install_supervisor [root@localhost ~]# systemctl start WANsupervisor [root@localhost ~]# systemctl enable WANsupervisor Step 4. Setup the Sensor Log into the Console to setup the Sensor(s). Sensors are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.

FILTER INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Install the Andrisoft repository. On the Console server, the Filter is already installed so you don't need to follow the installation steps listed below. [root@localhost ~]# rpm -Uvh https://packages.andrisoft.com/rhel8/wanrepo-8.4-0.noarch.rpm [root@localhost ~]# yum update Step 2. Install the packages Install the wanfilter package and its dependencies. Configure and start chrony (ntpd alternative) to prevent clock de-synchronization issues. [root@localhost ~]# yum install wanfilter [root@localhost ~]# cpanm Net::Telnet [root@localhost ~]# systemctl start chronyd [root@localhost ~]# systemctl enable chronyd Step 3. Configure and start the WANsupervisor service This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the WANsupervisor service, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console IP address and database password. [root@localhost ~]# /opt/andrisoft/bin/install_supervisor [root@localhost ~]# systemctl start WANsupervisor [root@localhost ~]# systemctl enable WANsupervisor Step 4. Remove local firewall rules The firewalld service overrules the Filter, and therefore has to be stopped. The Filter will manage the firewall rules. [root@localhost ~]# systemctl disable firewalld [root@localhost ~]# systemctl stop firewalld Step 5. Setup the Filter Log in to the Console to set up Filter(s). Filters are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.

BGP CONNECTOR INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Install the Andrisoft repository. On a Console, Sensor or Filter server, the necessary software is already installed so you don't need to follow the installation steps listed below. [root@localhost ~]# rpm -Uvh https://packages.andrisoft.com/rhel8/wanrepo-8.4-0.noarch.rpm [root@localhost ~]# yum update Step 2. Install the packages Install the wanbgp package and its dependencies. Configure and start chrony (ntpd alternative) to prevent clock de-synchronization issues. [root@localhost ~]# yum install wanbgp [root@localhost ~]# cpanm Net::Telnet [root@localhost ~]# systemctl start chronyd [root@localhost ~]# systemctl enable chronyd Step 3. Configure and start the WANsupervisor service This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the WANsupervisor service, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console IP address and database password. [root@localhost ~]# /opt/andrisoft/bin/install_supervisor [root@localhost ~]# systemctl start WANsupervisor [root@localhost ~]# systemctl enable WANsupervisor Step 4. Setup the BGP Connector Log in to the Console to set up BGP Connector(s).

Wanguard and Wansight can be installed on 64-bit architectures using the APT package manager.
All packages were tested on Debian 7 "Wheezy".

USER GUIDES:	Wanguard 8.0 User Guide
USER GUIDES:	Wansight 8.0 User Guide

CONSOLE INSTALLATION STEPS:	Step 1. Install the Andrisoft repository First add the Andrisoft repository to APT. debian:~# apt-get install apt-transport-https wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb https://www.andrisoft.com/files/debian7 wheezy main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wanconsole package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wanconsole debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Configure the MySQL service By default, MySQL is bound to the loopback interface so you must comment the bind-address parameter. If you deploy the Sensor or the Filter on remote systems, make sure that the MySQL server is accessible by opening port tcp/3306 in the firewall. debian:~# nano /etc/mysql/my.cnf #comment any "bind-address" directive, set "max_connections=1000", "max_allowed_packet=200M", "open_files_limit=5000" and add "skip-name-resolve", all in the [mysqld] section debian:~# service mysql restart Step 4. Restart the Apache service Reload the PHP configuration by restarting the Apache service. debian:~# service apache2 restart Step 5. Install the Console's database Finish installing the Console by running the /opt/andrisoft/bin/install_console script. Enter the MySQL root password, and provide a new password for the Console's database. debian:~# /opt/andrisoft/bin/install_console Step 6. Configure the Supervisor The WANsupervisor daemon must be installed and started on all systems. You have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password you set on step 5. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 7. Access the Console The Console web interface is accessible by pointing your web browser to http://<hostname>/wanguard or http://<hostname>/wansight, where <hostname> is the name of the server running the Console. The default username is "admin" with the password "changeme". Step 8. Install InfluxDB It is highly recommended to install influxdb from https://portal.influxdata.com/downloads and to switch the default graphing engine from rrdtool to influxdb. debian:~# wget https://dl.influxdata.com/influxdb/releases/influxdb_1.8.0_amd64.deb debian:~# dpkg -i ./influxdb_1.8.0_amd64.deb debian:~# cp /etc/influxdb/influxdb.conf /etc/influxdb/influxdb.conf.backup debian:~# cp /opt/andrisoft/etc/influxdb.conf /etc/influxdb/influxdb.conf debian:~# service influxdb restart

SENSOR INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Add the repository to APT if it's not already being used. debian:~# apt-get install apt-transport-https wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb https://www.andrisoft.com/files/debian7 wheezy main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wansensor package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wansensor debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Install, configure and start the Supervisor This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 4. Setup the Sensor Log into the Console to setup the Sensor(s). Sensors are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.

FILTER INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Add the repository to APT if it's not already being used. debian:~# apt-get install apt-transport-https wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb https://www.andrisoft.com/files/debian7 wheezy main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wanfilter package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wanfilter debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Install, configure and start the Supervisor This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 4. Setup the Filter Log in to the Console to set up Filter(s). Filters are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.

Wanguard and Wansight can be installed on 64-bit architectures using the APT package manager.
All packages were tested on Debian 6 "Squeeze".

USER GUIDES:	Wanguard 7.1 User Guide
	Wansight 7.1 User Guide

CONSOLE INSTALLATION STEPS:	Step 1. Install the Andrisoft repository First add the Andrisoft repository to APT. debian:~# apt-get install wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb http://www.andrisoft.com/files/debian6 squeeze main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wanconsole package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wanconsole debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Configure the MySQL service By default, the MySQL server does not have a password set. Start the MySQL server and set a password for the MySQL root user. By default MySQL is bound to the loopback interface, so you must comment the bind-address parameter. If you deploy the Sensor or the Filter on remote systems, make sure that the MySQL server is accessible by opening port tcp/3306 in the firewall. debian:~# nano /etc/mysql/my.cnf #comment any "bind-address" directive, enable "max_connections=600", edit "max_allowed_packet=64M" and add "skip-name-resolve", all in the [mysqld] section debian:~# service mysql start debian:~# /usr/bin/mysqladmin -u root password 'new-password' debian:~# service mysql restart Step 4. Reload the Apache service Please check that your distribution has PHP version 5.2 or above. debian:~# service apache2 restart Step 5. Install the Console's database Finish installing the Console by running the /opt/andrisoft/bin/install_console script. Enter the MySQL root password you set on step 3, and provide a new password for the Console's database. debian:~# /opt/andrisoft/bin/install_console Step 6. Configure the Supervisor The WANsupervisor daemon must be installed on all systems. You have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password you set on step 5. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 7. Access the Console The Console web interface is accessible by pointing your web browser to http://<hostname>/wanguard or http://<hostname>/wansight, where <hostname> is the name of the server running the Console. The default username is "admin" with the password "changeme". Continue with the installation of the Sensor by following the steps below.
SENSOR INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Add the repository to APT if it's not already being used. debian:~# apt-get install wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb http://www.andrisoft.com/files/debian6 squeeze main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wansensor package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wansensor debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Install, configure and start the Supervisor This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 4. Setup the Sensor Log into the Console to setup the Sensor(s). Sensors are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.
FILTER INSTALLATION STEPS:	Step 1. Install the Andrisoft repository Add the repository to APT if it's not already being used. debian:~# apt-get install wget debian:~# wget --no-check-certificate -O - https://www.andrisoft.com/andrisoft.gpg.key \| apt-key add - debian:~# echo "deb http://www.andrisoft.com/files/debian6 squeeze main" > /etc/apt/sources.list.d/andrisoft.list Step 2. Install the packages Install the wanfilter package and dependencies. Configure and start ntpd to prevent clock de-synchronization issues. debian:~# apt-get update debian:~# apt-get install wanfilter debian:~# service ntp start debian:~# update-rc.d ntp defaults Step 3. Install, configure and start the Supervisor This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. debian:~# /opt/andrisoft/bin/install_supervisor debian:~# service WANsupervisor start debian:~# update-rc.d WANsupervisor defaults 99 Step 4. Setup the Filter Log in to the Console to set up Filter(s). Filters are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.

WANGUARD and WANSIGHT can be installed using Ubuntu-compatible packages built for i686 ( 32 bit Intel or AMD ) and amd64 ( 64 bit Intel or AMD ) architectures. The installation instructions listed below contain references only for 64 bit packages. To install the packages on 32 bit CPUs, simply change the "amd64" string with "i686". The packages were tested on Ubuntu Server 13.10.

WANGUARD_5_4.pdf	WANGUARD 5.4 - User Manual and Administrator Guide.
WANSIGHT_5_3.pdf	WANSIGHT 5.4 - User Manual and Administrator Guide.
WANconsole-5.4-0.i686.deb	The Console is a web portal that provides single-point management and reporting for WANSIGHT and WANGUARD.
WANconsole-5.4-0.amd64.deb
WANsensor-5.4-0.i686.deb	The Sensor is the WANSIGHT and WANGUARD component that does traffic accounting, monitoring and analysis.
WANsensor-5.4-0.amd64.deb
WANfilter-5.4-0.i686.deb	The Filter is the WANGUARD component able to detect attackers and scrub malicious traffic.
WANfilter-5.4-0.amd64.deb
WANsupervisor-5.4-0.i686.deb	The Supervisor provides routines used to start, shutdown and monitor WANSIGHT and WANGUARD components.
WANsupervisor-5.4-0.amd64.deb
WANbgp-5.4-0.all.deb	The WANbgp package is used by WANGUARD for sending BGP routing announcements.

CONSOLE INSTALLATION STEPS:	Step 1. Install the Console's dependencies First make sure that all the required packages are installed. ubuntu:~# apt-get install mysql-server apache2 php5 php5-snmp php5-cli php5-mysql php5-json libdbd-mysql-perl libnet-telnet-perl quagga tshark rrdtool wget php5-mcrypt tcpdump ntp whois traceroute libnuma1 Step 2. Configure the MySQL server By default MySQL is bound to the loopback interface, so you should comment the bind-address parameter. If you deploy Sensors or Filters on remote systems, make sure that the MySQL server is accessible by opening port tcp/3306 in the firewall. ubuntu:~# nano /etc/mysql/my.cnf #comment any "bind-address" directive, enable "max_connections=300", edit "max_allowed_packet=64M" and add "skip-name-resolve", all in the [mysqld] section ubuntu:~# service mysql restart Step 3. Install the packages Install the packages WANsupervisor, WANconsole, WANsensor and WANbgp. ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANsupervisor-5.4-0.amd64.deb ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANconsole-5.4-0.amd64.deb ubuntu:~# dpkg -i WANsupervisor-5.4-0.amd64.deb WANconsole-5.4-0.amd64.deb ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANbgp-5.4-0.all.deb ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANsensor-5.4-0.amd64.deb ubuntu:~# dpkg -i WANbgp-5.4-0.all.deb WANsensor-5.4-0.amd64.deb Step 4. Configure the Apache server Add the line "zend_extension=/opt/andrisoft/webroot/ixed/ixed.5.5.lin" in php.ini, in the [PHP] section. ubuntu:~# nano /etc/php5/apache2/php.ini #add zend_extension=/opt/andrisoft/webroot/ixed/ixed.5.5.lin in the [PHP] section ubuntu:~# nano /etc/php5/cli/php.ini #add zend_extension=/opt/andrisoft/webroot/ixed/ixed.5.5.lin in the [PHP] section ubuntu:~# service apache2 restart Step 5. Install the Console's database Finish installing the Console by running the /opt/andrisoft/bin/install_console script. Enter the MySQL root password, and provide a new password for the Console's database. ubuntu:~# /opt/andrisoft/bin/install_console Step 6. Configure and start the Supervisor The WANsupervisor daemon must be installed and started on all systems. You have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password you set on step 5. If the Supervisor and Console are installed on the same system, don't use the loopback address 127.0.0.1 for the Console's IP address. Enter the IP address of the server. ubuntu:~# /opt/andrisoft/bin/install_supervisor ubuntu:~# service WANsupervisor start ubuntu:~# update-rc.d WANsupervisor defaults 99 Step 7. Access the Console The Console web interface is accessible by pointing your web browser to http://<hostname>/wanguard or http://<hostname>/wansight, where <hostname> is the name of the server running the Console. The default username is "admin" with the password "changeme". Continue with the installation of the Sensor by following the steps below.
SENSOR INSTALLATION STEPS:	Step 1. Install the Sensor's dependencies Install the required packages. Configure and start ntpd to prevent clock de-synchronization issues. ubuntu:~# apt-get install wget ntp libmysqlclient18 ubuntu:~# service ntp start Step 2. Install, configure and start the Supervisor This step is required if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANsupervisor-5.4-0.amd64.deb ubuntu:~# dpkg -i WANsupervisor-5.4-0.amd64.deb ubuntu:~# /opt/andrisoft/bin/install_supervisor ubuntu:~# service WANsupervisor start ubuntu:~# update-rc.d WANsupervisor defaults 99 Step 3. Install the Sensor Install the WANsensor package. ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANsensor-5.4-0.amd64.deb ubuntu:~# dpkg -i WANsensor-5.4-0.amd64.deb Step 4. Setup the Sensor Log into the Console to setup the Sensor(s). Sensors are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.
FILTER INSTALLATION STEPS:	Step 1. Install the Filter's dependencies Install the required packages. Configure and start ntpd to prevent clock de-synchronization issues. ubuntu:~# apt-get install tcpdump iptables wget ntp libmysqlclient18 ubuntu:~# service ntp start Step 2. Install, configure and start the Supervisor This step is necessary if you haven't previously installed and configured WANsupervisor on the target system. In order to configure the Supervisor, you have to run the /opt/andrisoft/bin/install_supervisor script to enter the Console's IP address and database password. ubuntu:~# /opt/andrisoft/bin/install_supervisor ubuntu:~# service WANsupervisor start ubuntu:~# update-rc.d WANsupervisor defaults 99 Step 3. Remove local firewall rules The iptables service overrules the Filter, and therefore has to be stopped. The Filter will manage the firewall rules from now on. ubuntu:~# update-rc.d iptables stop ubuntu:~# service iptables stop Step 4. Install the Filter Install the packages WANsensor and WANfilter. ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANsensor-5.4-0.amd64.deb ubuntu:~# wget http://www.andrisoft.com/files/ubuntu12/WANfilter-5.4-0.amd64.deb ubuntu:~# dpkg -i WANsensor-5.4-0.amd64.deb WANfilter-5.4-0.amd64.deb Step 5. Setup the Filter Log in to the Console to set up Filter(s). Filters are started, monitored and stopped by the WANsupervisor daemon, so make sure the WANsupervisor service is always running.